View MIC2590B11_1564562.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

mic2590b dual-slot pci hot plug controller micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 ( 408 ) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com september 2008 m9999-091808 general description the mic2590b is a power controller supporting power distribution requirements for peripheral component inter- connect (pci) hot plug compliant systems incorporating the intelligent platform management interface (ipmi). the mic2590b provides complete power control support for two pci slots including the 3.3v aux defined by the pci 2.2 specification. support for +5v, +3.3v, +12v and ?12v supplies is provided including programmable constant-current inrush limiting, voltage supervision, programmable current limit, fault reporting and circuit breaker functions which provide fault isolation. the mic2590b also incorporates a smbus interface in which complete status and control of power within each slot is provided. data such as voltage and current from each supply of each slot ca n be obtained for ipmi sensor records in addition to power status of each slot. data sheets and support documentation can be found on micrel?s web site at: www.micrel.com. features ? supports two independent pci 2.2 slots ? smbus interface for slot power control and status ? +5v, +3.3v, +12v, ?12v, +3.3vaux supplies supported per pci specification 2.2 ? programmable inrush current-limiting ? active current regulation controls inrush current ? electronic circuit breaker ? dual level fault detection for quick fault response without nuisance tripping ? thermal isolation between circuitry for slot a and slot b applications ? pci hot-plug power distribution ___________________________________________________________________________________________________________ ordering information part number standard pb-free 5v & 3v fast-trip threshold +12v & ?12v fast-trip threshold operating temp. range package mic2590b-2btq mic2590b-2ytq 100mv 1.5a/0.4a 0 to +70c 48-pin tqfp mic2590b-5btq* mic2590b-5ytq* disabled 1.5a/0.4a 0 to +70c 48-pin tqfp note: * contact factory for availability.
micrel, inc. mic2590b september 2008 2 m9999-091808 typical application vauxa 5vina 12vin1 12vin2 12mvin1 12mvin2 5vsena 5vgatea 5vouta vstby1 vstby2 12slewa 12slewb cfiltera 3.3vauxa pci bus 5v, 5a 3vina 3vsensea 3vgatea 3vouta 12vouta 12mvouta 5vinb 3.3v, 7.6a 12v, 0.5a 12v, 0.1a 5vsenseb 5vgateb 5voutb 3vinb 3vsenseb 3vgateb 3voutb 12voutb 12mvoutb vauxb 5v, 5a 3.3v, 7.6a 12v, 0.5a 12v, 0.1a 3.3vauxb r sense r 5vgatea r 3vgatea r 5vgateb r 3vgateb r sense r sense c gate c gate r sense pci bus 4.7f 4.7f 4.7f 4.7f mic2590b iref cfilterb gnd auxena/auxenb /faulta, /faultb a0 a1 a2 /int scl sda pci connector power supply +12v 12v +5.0v +3.3v vstby 1a schotty diode (clamp) /int scl sda smbus i/o management controller 2 sda scl /int 20k 1% hot-plug controller ona/onb auxena/auxenb /faulta, /faultb ona/onb 2 2 c gate c gate a bus switch b /oe
micrel, inc. mic2590b september 2008 3 m9999-091808 pin configuration 48-pin tqfp (tq) pin description pin number pin name pin function 6, 31 5vina, 5vinb 5v supply power and sense inputs [a/b]: two pins are provided for kelvin connection (one for each slot). pin 6 is the kelvin sense connection to the supply side of the sense resistor for 5v slot a. pin 31 is the kelvin sense connection to the supply side of the sense resistor for 5v slot b. these two pins must ultimately connect to each other within 10cm. an undervoltage lockout circuit (uvlo) prevents the switches from turning on while this input is less than its lockout threshold. 12, 25 3vina, 3vinb 3.3v supply power and sense inputs [a/b]: two pins are provided for kelvin connection (one for each slot). pin 12 is the kelvin sense connection to the supply side of the sense resistor for 3v slot a. pin 25 is the kelvin sense connection to the supply side of the sense resistor for 3v slot b. these two pins must ultimately connect to each other within 10cm. an undervoltage lockout circuit (uvlo) prevents the switches from turning on while this input is less than its lockout threshold. 5, 32 12vin ? 2 pins +12v supply input: an undervoltage lockout circuit prevents the switches from turning on while this input is less than its lockout threshold. both pins must be tied together at the chip. 17, 18 12vmin ? 2 pins ?12v supply input: an undervoltage lockout circuit prevents the switches from turning on while this input is less than it s lockout threshold. both pins must be tied together at the chip. 10, 27 12vouta, 12voutb 12v output [a/b] 19, 20 12mvouta, 12mvoutb ?12v output [a/b] 3, 34 12vslewa, 12vslewb 12v slew rate control [a/b]: connect capacitors between these pins and ground to set output slew rates of the +12v and -12v supplies.
micrel, inc. mic2590b september 2008 4 m9999-091808 pin number pin name pin function 45, 42 auxena, auxenb aux enable inputs [a/b]: rising-edge sensitive enable inputs for vauxa and vauxb outputs. taking auxena/auxenb low after a fault resets the respective slot?s aux output fault latch . tie these pins to ground if using smbus-mode power control. 16, 21 3vouta, 3voutb 3.3v power-good sense inputs: connect to 3.3v[a/b] outputs. used to monitor the 3.3v output voltages for power-good status. 9, 28 5vouta, 5voutb 5v power-good sense inputs: connect to 5v[a/b] outputs. used to monitor the 5v output voltages for power-good status. 33 iref a resistor connected between this pin and ground sets the adc current measurement gain. this resistor must be 20k ? 1%. 7, 30 5vsensea, 5vsenseb 5v circuit breaker sense input [a/b]: the current-limit thresholds are set by connecting sense resistors between these pins and 5vin[a/b]. when the current-limit threshold of ir = 50mv is reached, the 5vgate[a/b] pin is modulated to maintain a constant vo ltage across the sense resistor and therefore a constant current into the load. if the 50mv threshold is exceeded for t flt , the circuit breaker is tripped and t he gate pin for the affected slot is immediately pulled low. 13, 24 3vsensea, 3vsenseb 3v circuit breaker sense input [a/b]: the current limit thresholds are set by connecting sense resistors between these pins and 3vin[a/b]. when the current limit threshold of ir = 50mv is reached, the 3vgate[a/b] pin is modulated to maintain a constant vo ltage across the sense resistor and therefore a constant current into the load. if the 50mv threshold is exceeded for t flt , the circuit breaker is tripped and t he gate pin for the affected slot is immediately pulled low. 8, 29 5vgatea, 5vgateb 5v gate drive outputs [a/b]: each co nnects to the gate of an external n- channel mosfet. during power-up the c gate and the gate of the mosfets are charged by a 20a current source. this controls the value ofdv/dt seen at the source of the mosfets, and henc e the current flowing into the load capacitance. during current limit events, the voltage at this pin is adju sted to maintain constant current through the switch for a period of t flt . whenever an overcurrent, thermal shutdown or input undervoltage fault condition occur sthe gate pin for the affected slot is immediately brought low. during power-down these pins are discharged by an internal current source. 14, 23 3vgatea, 3vgateb 3v gate drive outputs [a/b]: each co nnects to the gate of an external n- channel mosfet. during power-up the c gate and the gate of the mosfets are charged by a 20a current source. this controls the value ofdv/dt seen at the source of the mosfets, and henc e the current flowing into the load capacitance. during current limit events, the voltage at this pin is adju sted to maintain constant current through the switch for a period of t flt . whenever an overcurrent, thermal shutdown or input undervoltage fault condition occurs the gate pin for the affected slot is immediately brought low. during power-down these pins are discharged by an internal current source. 11, 26 vstby ? 2 pins 3.3v standby input voltage required to support pci 2.2 vaux input: smbus, internal registers and a/d converter run off of vstby to ensure chip access during standby modes. a uvlo circuit pr events turn-on of this supply until vstby rises above its uvlo threshold. bo th pins must be tied together at the chip. 15, 22 vauxa, vauxb v aux [a/b] output voltages to pci card sl ots: these output s connect the vaux pin of the pci 2. 2 connectors vstby via internal 400m ? mosfets which are current-limited and pr otected against short circuit faults. 44, 43 ona, onb enable input for main outputs: rising- edge sensitive. used to enable or disable main (5v, 3.3v, +12v, ?12v) outputs. taking ona/onb low after a fault resets the respective slot?s main output fault latch. tie these pins to ground if using smbus-mode power control.
micrel, inc. mic2590b september 2008 5 m9999-091808 pin number pin name pin function 1, 36 /faulta, /faultb open drain, active-low: asserted whenever the circuit breaker trips due to a fault condition. /fault[a/b] is reset by br inging the faulted slot?s on pin low if /fault was asserted in response to a fault condition on one of the slot?s main outputs(+12v, +5v, +3.3v, or ?12v). /fault[a/b] is reset by bringing the faulted slot?s auxen pin low if /fault was asserted in response to a fault condition on the slot?s vaux output. if a fault condition occurred on both the main and aux outputs of the same slot, then both on and auxen must be brought low to de-assert the /fault output. 2, 35 cfiltera, cfilterb filter capacitor [a/b]: capacitors conn ected between these pins and ground set the duration of t flt . t flt is the amount of time for which a slot remains incurrent- limit before its circuit breaker is tripped. 37 /int interrupt output: open drain, active-low. asserted whenever a power faulti s detected. cleared by writing a logic 1 to t he respective active bit into the status register. 48 sda smbus data: bidire ctional smbus data line. 47 scl smbus clock: input. 39, 40, 41 a2, a1, a0 smbus address select pins: connect to ground or leave open in order to program device smbus base address. there is an internal pull-up to vstby on each of these inputs. 4, 38 gpia, gpib general purpose inputs: t he state of these inputs are available by reading the common status register. 46 gnd ground
micrel, inc. mic2590b september 2008 6 m9999-091808 absolute maximum ratings (1) supply voltage (12v in ) ..........................................................................+14v (12mv in ) .......................................................................?14v (5v in ) ..............................................................................+7v (3v in ), (v stby ) .................................................................+7v any logic output voltage ............... ?0.5 (min)/+5.5v (max) any logic input voltage ................... ?0.5 (min)/+5.5v (max output current (failt[a/b]#, /int, sda). ..................10ma lead temperature ir reflow, peak temp erature.......................... 235 +5/?0c storage temperature (t s ) .........................?65c to +150c esd rating (3) .................................................................. 2kv operating ratings (2) supply voltage (12v in ) .................................................... +11.65v to +12.6v (12mv in ) ................................................... ?11.0v to ?13.2v (5v in ) .......................................................... +4.85v to 5.25v (3v in ) ............................................................ +3.1v to +3.6v (v stby ) ......................................................... +3.15v to 3.6v ambient temperature (t a ) .............................. 0c to +70c junction temperature (t j ) ......................................... 125c thermal resistance tqfp ( ja ) ......................................................56.5c/w electrical characteristics (4) 12v in = 12v; 12mv in = ?12v; 5v in = 5v; 3v in = 3.3v; v stby = 3.3v; t a = 0c to 70c; unless noted. power control and logic sections symbol parameter condition min typ max units i cc12 i cc5 i cc33 i cc12m i ccvsby supply current 0.6 1.2 0.5 ?1.0 2.5 2.0 2.0 0.7 ?2.0 5.0 ma ma ma ma ma v uvlo under voltage lockout 12v in increasing 3v in increasing 5v in increasing 12mv in increasing v stby increasing 8 2.2 3.7 ?10 2.8 9 2.5 4.0 ?9 2.9 10 2.75 4.3 ?8 3.0 v v v v v v hysuv under voltage lockout hysteresis - 12v in , 12mv in , 5v in , 3v in 180 mv v hysstby under-voltage lockout hysteresis - v stby 50 mv v uvth v uvth(12v) v uvth(12mv) v uvth(3v) v uvth(5v) v uvth(vaux) power good under-voltage thresholds 12v out [a/b] 12mv out [a/b] 3v out [a/b] 5v out [a/b] v aux [a/b] 12v out [a/b] decreasing 12mv out [a/b] decreasing 3v out [a/b] decreasing 5v out [a/b] decreasing v aux [a/b] decreasing 10.2 ?10.8 2.7 4.4 2.7 10.5 ?10.6 2.8 4.5 2.8 10.8 ?10.2 2.9 4.7 2.9 v v v v v v hyspg power-good detect hysteresis 30 mv v gate 5v gate /3v gate voltage 12v in ?15 12v in v i gate(source) 5v gate /3v gate output source start cycle 15 25 35 a i gate(sink ) 5v gate /3v gate output sink fault current any fault condition, v gate = 5v 70 ma
micrel, inc. mic2590b september 2008 7 m9999-091808 symbol parameter condition min typ max units v filter c filter threshold voltage 1.20 1.25 1.30 v i filter c filter [a/b] charge current v [5/3] v in ? v [5/3] v sense > v thilimit 1.80 2.5 5.0 a i slew 12v slew [a/b] charge current during turn-on only 13 22 35 a v thilimit current limit threshold voltages 5v[a/b] supplies 3.3v[a/b] supplies v 5vin ? v 5vsense v 3vin ? v 3vsense 35 35 50 50 65 65 mv mv v thfast 5v out [a/b] and 3v out [a/b] fast-trip thresholds mic2590b-2 mic2590b-5 90 113 disabled 135 mv v il low-level input voltage (scl,sda,on[a/b],a [0-2],gpi[a/b]) 0.8 v v ol output low voltage /fault[a/b], /int, sda i ol = 3ma 0.4 v v ih high-level input voltage scl,sda,on[a/b],a[0-2], auxen[a/b],gpi[a/b]) 2.1 v r pull-up internal pullups from a[0-2] to v stby 40 k ? i il input leakage current scl, on[a/b],auxen[a/b], gp[a/b]) 5 a i lkg(off) off-state leakage current sda,/fault[a/b],/int 5 a overtemperature shutdown & reset thresholds, with overcurrent on slot t j increasing, each slot, note 5 t j decreasing, each slot, note 5 140 130 c c t ov overtemperature shutdown & reset thresholds, all other conditions (all outputs will latch off) t j increasing, both slots, note 5 t j decreasing, both slots, note 5 160 150 c c r out(on) r out(12v) r out(12mv) r out(aux) output mosfet resistance 12v mosfet ?12v mosfet v aux mosfet i ds = 500ma, t j = 125c i ds = 100ma, t j = 125c i ds = 375ma, t j = 125c 500 2 400 m ? ? m ? v off v off(+12v) v off(?12v) v off(aux) off-state output offset voltage 12v out [a/b] 12mv out [a/b] v aux [a/b] 12v out [a/b] = off, t j = 125c 12mv out [a/b] = off, t j = 125c v aux [a/b] = off, t j = 125c ?50 50 50 mv mv mv i thslow i lim(12) i lim(12m) current limit threshold 12v mosfet ?12v mosfet 12v out [a/b] = 0v 12mv out [a/b] = 0v 0.52 ?0.11 1.0 ?0.2 1.5 ?0.3 a a i thfast fast-trip thresholds 12v out [a/b] (mic2590b-2) 12mv out [a/b] (mic2590b-2) 1.0 ?0.20 2.15 ?0.45 3.0 ?0.6 a a i aux(thresh) auxiliary output current limit threshold figure 4 current which must be drawn from v aux to register as a fault 0.84 a i sc(tran) maximum transient short circuit current v aux enabled, then grounded i max = v stby / r ds(aux) a
micrel, inc. mic2590b september 2008 8 m9999-091808 symbol parameter condition min typ max units i lim(aux) regulated current after transient from end of i sc(tran) to c filter time out 0.375 0.7 1.35 a r disch r (12v) r (12mv) r (3v) r (5v) r (3vaux) output discharge resistance 12v out [a/b] 12mv out [a/b] 3v out [a/b] 5v out [a/b] 3v aux [a/b] 12v out [a/b] = 6.0v 12mv out [a/b] = ?6.0v 3v out [a/b] = 1.65v 5mv out [a/b] = 2.5v 5v out [a/b] = 1.65v 1600 600 150 150 430 ? ? ? ? ? t off(3) t off(5) current limit response time for 3.3v and 5v outputs, figure 2 mic2590b-2 with c gate = 10nf, v in ? v sense = 200mv 1 s t sc(tran) v aux current limiter response time, figure 5 v aux [a/b] = 0v, note 5 33 s t off(12) 12v current limit response time, figure 3 12v out [a/b] = 0v, note 5 1 s t off(12m) ?12v current limit response time, figure 3 12mv out [a/b] = 0v, note 5 1 s t prop(3vfault) delay from 3v[a/b] overcurrent-limit to fault output mic2590b-2, v sense ? v thlimit = 200mv, c filter = open 1 s t prop(5vfault) delay from 5v[a/b] overcurrent-limit to fault output mic2590b-2, v sense ? v thlimit = 200mv, c filter = open 1 s t w on[a/b], auxen[a/b] pulse width note 5 100 ns t por mic2590b power-on reset time after vstby becomes valid note 5 500 s 8-bit analog to digital converter total unadjusted error voltage, all outputs current, 3v out [a/b]/5v out [a/b] current, v aux [a/b], 12v out [a/b], 12mv out [a/b] measured as voltage across corresponding external r sense ?3 ?3 3 +3 +3 % % % t conv conversion time 60 100 ms v auxa v auxb resolution specifications: full scale voltage lsb of voltage full scale current lsb of current 3.85 15.1 375 1.47 v mv ma ma 3v outa 3v outb full scale voltage lsb of voltage full scale current lsb of current external r sense = 6.00m ? 3.85 15.1 11.6 45.5 v mv a ma 5v outa 5v outb full scale voltage lsb of voltage full scale current lsb of current external r sense = 6.00m ? 5.89 23.1 6.96 27.3 v mv a ma
micrel, inc. mic2590b september 2008 9 m9999-091808 symbol parameter condition min typ max units 12v outa 12v outb full scale voltage lsb of voltage full scale current lsb of current 13.8 54.1 6.96 27.3 v mv ma ma 12mv outa 12mv outb full scale voltage lsb of voltage full scale current lsb of current ?13.6 53.5 100 0.392 v mv ma ma smbus timing, note 5 t 1 scl (clock) period figure 1 2.5 s t 2 data in set-up time to scl high figure 1 100 ns t 3 data out stable after scl low figure 1 300 ns t 4 data low set-up time to scl low start condition, figure 1 100 ns t 5 data high hold ti me after scl high start condition, figure 1 100 ns notes: 1. exceeding the absolute maxi mum rating may damage the device. 2. the device is not guaranteed to function outside its operating rating. 3. devices are esd sensitive. handling precautions recommended. human body model, 1.5k ? in series with 100pf. 4. see applications section. 5. parameters guaranteed by design. not 100% production tested.
micrel, inc. mic2590b september 2008 10 m9999-091808 test circuit t 1 t 4 scl sda data in sda data out t 2 t 5 t 3 figure 1. smbus timing 1v 3vgate/5vgate v thfast t off3/5 v thfast figure 2. 3v/5v current limit response timing i thfast i lim12[m] t off12[m] i out i out(aux) i out(aux) i lim(aux) must trip may not trip i aux(thresh) figure 3. +12v/?12v current li mit response timing figure 4. vaux current limit threshold i out(aux) t sc(tran) i lim(aux) i sc(tran) figure 5. vaux current limit response timing
micrel, inc. mic2590b september 2008 11 m9999-091808 functional description hot swap insertion when circuit boards are inserted into systems carrying live supply voltages (?hot plugged?), high inrush currents often result due to the char ging of bulk capacitance that resides across the circuit board?s supply pins. this transient inrush current can cause the system?s supply voltages to temporarily go out of regulation, causing data loss or system lock-up. in more extreme cases, the transients occurring during a hot plug event may cause permanent damage to connectors or on-board components. the mic2590b addresses these issues by limiting the inrush currents to the load (pci board), and thereby controlling the rate at which the load?s circuits turn on. in addition, the mic2590b offers input and output voltage supervisory functions and current-limiting to provide robust protection for both the host system and the pci board. system interfaces the mic2590b employs two system interfaces. one is the hot plug interface (hpi) which includes on[a/b], auxen[a/b], and /fault[a/b]. the other is the system management interface (smi) consisting of sda, scl and /int, (whose signals conform to the specifications and format of intel?s smbus standard). the mic2590b can be operated exclusively from the smi, or can employ the hpi for power control while continuing to use the smi for access to all but the power control registers. in addition to the basic power control features of the mic2590b accessible by the hpi, the smi also gives the host access to the following information from the part: 1. output voltage from each supply. 2. output current from each supply. 3. fault conditions occurring on each supply. when using the system management interface for power control, do not use the hot plug interface. conversely, when using the hpi for power control, do not execute power control commands over the smi bus (all other register accesses via the smi bus remain permissible while in the hpi control mode). note that if power control is performed via the smi bus, the auxena, auxenb, ona and onb pins should be tied to ground. power-on reset and power cycling the mic2590b utilizes v stby as the main supply input source. it is required for proper operation of the mic2590b smbus, registers and adc and must be applied at all times. a power-on reset (por) cycle is initiated after v stby rises above its uvlo threshold and remains valid at that voltage for 500s. all internal registers except result are cleared after por. if v stby is recycled the mic2590b enters a new power-on reset cycle. v stby must be the first supply input applied. following the por interval, the main supply inputs of 12v in , 12mv in , 5v in and 3v in may be applied in any order. the smbus is ready for acce ss at the end of the por interval. during t por all outputs are off. power-up cycle (see typical application circuit) when a slot is off, the 5v gate and 3v gate pins are held low with an internal pull-down current source. when a slot?s main outputs are enabl ed, and all input voltages are above their respective undervol tage lockout thresholds, all four main supplies execute a controlled turn on. at this time, the gate voltages of the 5v and 3.3v mosfets are ramped at a controlled rate from 0v to approximately 11.5v. this is sufficient to fully enhance the external mosfets for lowest possible dc losses. the ramp rate is controlled by 25a (typ.) current sources from the gate pins charging each c gate . the magnitude and slew rate of the output current is proportional to the value of c gate and the load capacitance. the minimum value of c gate is selected to ensure that during start-up the load current does not exceed the cu rrent-limit threshold. the following equation is used to determine the value of c gate (min): load lim gate gate c i i (min) c = where c load is the load capacitance connected to the 3.3v and 5v outputs and i lim and i gate are respectively the current-limit and gate charge current specifications as given in the electrical charac teristics table. the output slew rate dv/dt is computed by: 6 gate gate 10 c i ) dv/dt(load = i slew = 25a c gate dv/dt (load) 0.001f 25000v/s 0.01f 2500v/s 0.1f 250v/s 1f 25v/s table 1. 3.3v/5v output slew rate selection for the +12v and ?12v supplies, the output slew rate is controlled by capacitors connected to the 12v slewa and 12v slewb pins. to determine the minimum value of the slew rate capacitor, (c slew ), connected to 12v slew [a/b], the following equation is used: load lim slew slew c i i (min) c = where c load is the load capacitance connected to the +12v and ?12v outputs, and i lim and i slew are respectively the current-limit and slew rate charge current values found in the electrical characteristics table. the
micrel, inc. mic2590b september 2008 12 m9999-091808 equation above computes the minimum value to guarantee the device does not enter into current limit. the slew rate dv/dt is computed by: 6 slew slew 10 c i load at dv/dt = by appropriate selection of the value of c slew , it can be ensured that the magnitude of the inrush current never exceeds the current limit for a given load capacitance. since one capacitor fixes the slew rate for both +12v and ?12v, the capacitor value should be chosen to provide the slower slew rate of the two. table 2 depicts the output slew rate for various values of c slew . i slew = 25a c gate dv/dt (load) 0.001f 22000v/s 0.01f 2200v/s 0.1f 220v/s 1f 22v/s table 2. 12v output slew rate selection power down cycle when a slot is turned off, inte rnal switches are connected to each of the outputs to discharge the pci board's bypass capacitors to ground. standby mode standby mode is entered when any one (or more) enabled main supply input(s) (12v in , 12mv in , 5v in and 3v in ) drops below its respective uvlo threshold. the mic2590b supplies two 3.3v auxiliary outputs, v aux [a/b], satisfying pci 2.2 specificat ions. these outputs are fed via the v stby input, and controlled by the auxen[a/b] inputs or via their smi bus control registers. these outputs are independent of the main outputs: should one or more of the main supply inputs move below its uvlo thresholds, v aux [a/b] still function as long as v stby is present. prior to entering standby mode, ona and onb (or the maina and mainb bits in the control registers) inputs should be de-asserted. if this is not done, the mic2590b will assert /fault, and also /int if interrupts are enabled, when the mic2590b detects an undervoltage condition on a supply input. circuit breaker functions the mic2590b provides an electronic circuit breaker function that protects agains t excessive loads such as short circuits at each supply. when the current from one or more of a slot?s main ou tputs exceeds the current limit threshold (50mv/r sense for 3.3v and 5v, 1.0a for +12v, and/or 0.2afor ?12v) for a duration greater than t flt , the circuit breaker is tripped and all main supplies (all outputs except v aux [a/b]) are shut off. should the load current exceed i thfast (+12v and ?12v), or cause a main output?s v sense to exceed v thfast (+3.3v and +5v), the outputs are shut off with no delay. undervoltage conditions on the main supply i nputs also trip the circuit breaker, but only when the main outputs are enabled (to signal a supply input brown-out condition). the v aux [a/b] outputs have their own separate circuit breaker functions. v aux [a/b] do not incorporate a fast-trip threshold, but instead regulate the output current into a fault to avoid exceeding their operating current limit. the circuit breaker will trip due to overcurrents on v aux [a/b] when the fault timer expires. this use of the t flt timer prevents the circuit breaker from tripping prematurely due to brief current transients. following a fault condition, the outputs can be turned on again via the on inputs (if the fault occurred on one of the main outputs), via the auxen inputs (if the fault occurred on the aux outputs), or by cycling both on and auxen (if faults occurred on both the main and aux outputs). a fault condition can alternatively be cleared under smi control of the enable bits in the c ntrl [a/b] registers. when the circuit breaker tr ips, /fault[a/b] will be asserted if the outputs were enabled through the hot plug interface (non-smi mode) inputs. at the same time, /int will be asserted (unless interrupts are masked). note that /int is de-asserted by writing a logic 1 back into the respective fault bit position(s) in the stat[a/b] register or the common status register. t flt is set by external capacitors, c fil [a/b], connected to the c filter [a/b] pins. the equation below can be used to determine the capacitor value for a given duration of t flt : ? ? ? ? ? ? ? ? ? 1second t 2.0 . c flt fil thermal shutdown the internal +12v, ?12v and vaux mosfets are protected against damage not only by current limiting, but by dual-mode over-temperatur e protection as well. each slot controller on the mic2590b is thermally isolated from the other. should an overcurrent condition raise the junction temperature of one slot?s controller and internal pass elements to 140c, all of the outputs for that slot (including v aux ) will be shut off, and the slot?s /fault output will be asserted. the other slot?s operation will remain unaffected. however, should the mic2590b?s overall die temperature ex ceed 160c, both slots (all outputs, including v auxa and v auxb ) will be shut off, whether or not a current-limit condition exists. a 160c overtemperature condition additionally sets the overtemperature bit (ot_int) in the common status register. a/d converter the mic2590b has a 20-channel, 8-bit a/d converter capable of monitoring the output voltage and current of each supply. this information is available via the system management interface. the information is particularly
micrel, inc. mic2590b september 2008 13 m9999-091808 intended for use by systems that support the ipmi standard, but may be used for any desired purpose. interrupt generation in the mic2590b, the /int pin can be asserted (driven low) whenever a fault condition trips the circuit breaker. the mic2590b can thus operate in either polled mode or interrupt mode. in the polled mode, the interrupt mask bit in the common status register should be set, to prevent the /int pin from being asse rted. upon a circuit breaker fault event the appropriate stat us bit is also set in the corresponding status registers. in order to clear the status bit the system must write a l ogic 1 back to same bit in the status register. upon occurrenc e of the write the /int pin will be de-asserted (if interrupts were enabled), if no other interrupts are pending. this method of ?echo reset? allows data to be retained in the status registers until such time as the system software is ready to deal with that data, and then to control the earliest time at which the next interrupt might occur. system management interface (smi) the mic2590b?s system managem ent interface uses the read_byte and write_byte s ubset of the smbus protocols to communicate with its host via the system management interface bus. additionally, the /int output signals the controlling processo r that one or more events need attention, if an interrupt-driven architecture is used. note that themic2590b does not participate in the smbus alert response address (ara ) portion of the smbus protocol. the smbus read_byte operation consists of sending the device?s slave address, followed by the target register?s internal address, and then clocking out the byte to be read from the target register. similarly, the write_byte operation consists of sending the device?s slave address, followed by the target register?s internal address, and then clocking in the byte to be written to the target register. the target register addresses for the mic2590b are given in table 4. mic2590b smbus address configuration the mic2590b responds to its own unique address which is assigned using a2, a1 and a0. these represent the 3 lsbs of its 7-bit address, as shown in table 3. these address bits are assigned only during power up of the v stby supply input. these three bits allow up to eight mic2590b devices in a single system. these pins are either grounded or left unconnected to specify a logical 0 or 1 respectively. a pin designated as a logical 1 may also be pulled up to v stby . inputs mic2590b slave addresses a2 a1 a0 binary hex 0 0 0 1000 000 b 80 h 0 0 1 1000 001 b 82 h 0 1 0 1000 010 b 84 h 0 1 1 1000 011 b 86 h 1 0 0 1000 100 b 88 h 1 0 1 1000 101 b 8a h 1 1 0 1000 110 b 8c h 1 1 1 1000 111 b 8e h table 3. mic2590b smbus addressing auxen[x] on[x] aux out[x] main out[x] fault detected on aux out[x] fault detected on main out[x] /fault output[x] /int output (cleared by software) figure 6. hot plug interface mode operation
micrel, inc. mic2590b september 2008 14 m9999-091808 s1000 1a x 00000 xxxa x x x /a xx p mic2590b slave address master to slave transfer, i.e., data driven by master. x slave to master transfer, i.e., data driven by slave. data clk target registe r value read from mic2590b start stop r/w = read acknowledge not acknowledge figure 7. read_byte protocol s1000 0a 00000 xxxaxx x /a xx p mic2590b slave address master to slave transfer, i.e., data driven by master. slave to master transfer, i.e., data driven by slave. data clk target registe r value to be written to mic2590b start stop r/w = write acknowledge not acknowledge xx figure 8. write_byte protocol register set and programmer?s model target register common byte value label description read write power-on default result adc conversion result register 00h n/a n/a adcntrl adc control register 01 h 01 h 00 h cntrla control register slot a 02 h 02 h 00 h cntrlb control register slot b 03 h 03 h 00 h stata slot a status 04 h 04 h 00 h statb slot b status 05 h 05 h 00 h stat common status register 06 h 06 h 00 h
micrel, inc. mic2590b september 2008 15 m9999-091808 detailed register descriptions below: conversion result register (result), 8-bits read only d[7] read-only d[6] read-only d[5] read-only d[4] read-only d[3] read-only d[2] read-only d[1] read-only d[0] read-only voltage or current data from adc bit function operation d[7:0] measure data from adc read only power-up default value: undefined following por read command byte: 0000 0000 b = 00 h (adc control register adcntrl), 8-bits read/write d[7] read-only d[6] read-only d[5] read-only d[4] read- write d[3] read- write d[2] read- write d[1] read- write d[0] read- write busy reserved reserved sel par supply select sup[2:0] bit(s) function operation busy adc status 0 = adc quiescent 1 = adc busy d[6] reserved always read as zero d[5] reserved always read as zero sel a/d slot select specifies channel for a/d conversion 0 = slot a 1 = slot b par parameter control bit for adc conversion 0 = current 1 = voltage sup[2:0] supply select for adc conversion 000 = no conversion 001 = 3.3v supply 010 = 5.0v supply 011 = +12v supply 100 = -12v supply 101 = vaux supply power-up default value: 0000 0000 b = 00 h command byte (r/w): 0000 0001 b = 01 h to operate the adc the adcntrl register must first be initialized by selecting a slot, specifying whether voltage or current is to be measured and then specifying the specific supply that is to be monitored. the software must then wait 100ms, or poll the busy bit until it is zero. the result register will then contain the valid result of the conversion. control register, slot a (cntrlb), 8-bits read/write d[7] read-only d[6] read-only d[5] read-only d[4] read-only d[3] read-only d[2] read-only d[1] read-write d[0] read-write auxapg mainapg reserved reserved reserved reserved maina auxa bit(s) function operation auxapg aux output power- good status, slot a 1 = power-good (vauxa output is above its v uvth threshold) mainapg main output power- good status, slot a 1 = power-good (maina output is above its v uvth threshold) d[5] reserved always read as zero d[4] reserved always read as zero d[3] reserved always read as zero d[2] reserved always read as zero maina main enable control, slot a 0 = off, 1 = on vauxa vaux enable control, slot a 0 = off, 1 = on power-up default value: 0000 0000 b = 00 h command byte (r/w): 0000 0010 b = 02 h the power-up default value is 00h. slot a is disabled upon power-up, i.e., all supply outputs are off. control register, slot b ( cntrlb), 8-bits read/write d[7] read-only d[6] read-only d[5] read-only d[4] read-only d[3] read-only d[2] read-only d[1] read-write d[0] read-write auxbpg mainbpg reserved reserved reserved reserved mainb auxb bit(s) function operation auxbpg aux output power- good status, slot b 1 = power-good (vauxb output is above its v uvth threshold) mainbpg main output power- good status, slot b 1 = power-good (mainb output is above its v uvth threshold) d[5] reserved always read as zero d[4] reserved always read as zero d[3] reserved always read as zero d[2] reserved always read as zero mainb main enable control, slot b 0 = off, 1 = on vauxb vaux enable control, slot b 0 = off, 1 = on power-up default value: 0000 0000 b = 00 h command byte (r/w): 0000 0011 b = 03 h the power-up default value is 00h. slot b is disabled upon power-up, i.e., all supply outputs are off.
micrel, inc. mic2590b september 2008 16 m9999-091808 status register, slot a (stata), 8-bits read only d[7] read-only d[6] read-only d[5] read-only d[4] read- write d[3] read- write d[2] read- write d[1] read- write d[0] read- write faulta maina vauxa vauxaf 12mvaf 12vaf 5vaf 3vaf bit(s) function operation faluta fault pin status, slot a notes 1 & 2 maina main enable status, slot a represents actual state (on/off) of the four main power outputs for slot a. (+12v, +5v, +3.3v and -12v) 1 = main power on 0 = main power off vauxa vaux enable status, slot a represents actual state (on/off) of the auxiliary power outputs for slot a. 1 = main power on 0 = main power off vauxfa overcurrent fault vaux supply 1 = fault 0 = no fault 12mvfa overcurrent fault -12v supply 1 = fault 0 = no fault 12vfa overcurrent fault 12v supply 1 = fault 0 = no fault 5vfa overcurrent fault 5v supply 1 = fault 0 = no fault 3vfa overcurrent fault 3v supply 1 = fault 0 = no fault power-up default value: 0000 0000 b = 00 h read command byte (r/w): 0000 0100 b = 04 h the power-up default value is 00h. the slot is disabled upon power-up, i.e., all supply ou tputs are off. in response to an overcurrent fault condition, writing a logical 1 back into the active (or set) bit position will clear the bit and de- assert /int. the status of the /faulta pin is not affected by reading the status register. status register, slot b (statb), 8-bits read only d[7] read-only d[6] read-only d[5] read-only d[4] read- write d[3] read- write d[2] read- write d[1] read- write d[0] read- write faultb mainb vauxb vauxbf 12mvbf 12vbf 5vbf 3vbf bit(s) function operation falutb fault pin status, slot b notes 1 & 2 mainb main enable status, slot b represents actual state (on/off) of the four main power outputs for slot b. (+12v, +5v, +3.3v and -12v) 1 = main power on 0 = main power off vauxb vaux enable status, slot b represents actual state (on/off) of the auxiliary power outputs for slot b. 1 = main power on 0 = main power off vauxfb overcurrent fault vaux supply 1 = fault 0 = no fault 12mvfb overcurrent fault -12v supply 1 = fault 0 = no fault 12vfb overcurrent fault 12v supply 1 = fault 0 = no fault 5vfb overcurrent fault 5v supply 1 = fault 0 = no fault 3vfb overcurrent fault 3v supply 1 = fault 0 = no fault power-up default value: 0000 0000 b = 00 h read command byte (r/w): 0000 0101 b = 05 h the power-up default value is 00h. the slot is disabled upon power-up, i.e., all supply ou tputs are off. in response to an overcurrent fault condition, writing a logical 1 back into the active (or set) bit position will clear the bit and de- assert /int. the status of the /faultb pin is not affected by reading the status register. note 1 . 1 = /fault[a/b] pin asserted, indica ting a fault condition (/fault is low). 0 = /fault[a/b] pin is de-asserted (/fault is high). if fault[a/b] has been set by an overcurrent condition on one (or more) of the main outputs, the corresponding on[a/b] must go low to reset fault. if fault[a/b] has been set by an overcurrent on a vaux output, the corresponding auxen[a/b] must go low to rese t fault. if an overcurrent has occurred on both a main output and vaux output of a slot, both on[a/b] and auxen[a/b] of the corresponding slot must go low to reset fault. note 2 . the fault bits, and the /fault pins, are not active when th e mic2590b power paths are controlled by the system management interface (smbus). when using smi power path control for a slo t, the auxen and on pins for that slot must be tied to ground.
micrel, inc. mic2590b september 2008 17 m9999-091808 common status register, (stat), 8-bits read/write d[7] read-only d[6] read-only d[5] read-only d[4] read-only d[3] read- write d[2] read- write d[1] read- write d[0] read-only reserved reserved gpib gpia intmsk uv_int ot_int reserved bit(s) function operation d[7] reserved always read as zero d[6] reserved always read as zero gpib general purpose input, slot b state of gpib pin gpia general purpose input, slot a state of gpia pin intmsk interrupt mask 0 = /int generation is enabled 1 = /int generation is disabled. the mic2590b does not participate in the smbus alert response address (ara) protocol. uv_int undervoltage interrupt set whenever a circuit interrupt breaker fault condition occurs as a result of an undervoltage lockout condition on one of the main supply inputs. this bit is only set if a uvlo condition occurs while one or both of the on[a/b] pins are asserted or the main[a/b] enable control bits are set. ot_int overtemperature interrupt set whenever a circuit breaker fault occurs as a result of an overtemperature condition exceeding 160c shutting both channels off. d[0] reserved read undefined power-up default value: 0000 0000 b = 00 h command byte (r/w): 0000 0110 b = 06 h to reset the ot_int and uv_int fault bits a logical 1must be written back to these bits.
micrel, inc. mic2590b september 2008 18 m9999-091808 application information current sensing for the three power supplies switched with internal mosfets (+12v, ?12v, and v aux ), the mic2590b provides all necessary current sensing functions to protect the ic, the load, and the power supply. for the remaining four supplies which the part is designed to control, the high currents at which these supplies typically operate makes sensing the current inside the mic2590b impractical. therefore, each of these supplies (3va, 5va, 3vb, and 5vb) requires an external current sensing resistor. the v in connection to the ic from each supply (e.g., 5v ina ) is connected to the positive terminal of the slot?s current sense amplifier, and the corresponding sense input (in this case, 5v sensea ) is connected to the negative terminal of the current sense amplifier. sense resistor selection the mic2590b uses low-value sense resistors to measure the current flowing through the mosfet switches to the loads. these sense resistors are nominally valued at 50m ? /i load(cont) . to accommodate worst-case tolerances for both the sense resistor, (allow 3% over time and temperature for a resistor with 1% initial tolerance) and still supply the maximum required steady-state load current, a slightly more detailed calculation must be used. the current limit threshold voltage (the ?trip point?) for the mic2590b may be as low as 35mv, which would equate to a sense resistor value of 35m ? /i load(cont) . carrying the numbers through for the case where the value of the sense resistor is 3% high, this yields: () () load(cont) load(cont) sense i 34m ? i 1.03 35m ? r = = once the value of r sense has been chosen in this manner, it is good practice to check the maximum i load(cont) which the circuit may let through in the case of tolerance build-up in the opposite direction. here, the worst-case maximum is found using a 65mv trip voltage and a sense resistor which is 3% low in value. the resulting current is: () () sense(nom) sense(nom) max) load(cont, r 67m ? r 0.97 65m ? i = = as an example, if an output mu st carry a continuous 4.4a without nuisance trips occurring, r sense for that output should be 34m ? /4.4a = 7.73m ? . the nearest standard value is 7.5m ? , so a 7.5m ? 1% resistor would be a good choice. at the other set of tolerance extremes, i load(cont, max) for the output in question is then simply 67mv/7.5m ? = 8.93a. knowing this final datum, we can determine the necessary wattage of the sense resistor, using p = i 2 r. here i will be i load(cont, max) , and r will be (0.97)(r sense(nom) ). these numbers yield the following: p max = (8.93a) 2 (7.28m ? ) = 0.581w a 1.0w sense resistor would wo rk well in this application. kelvin sensing because of the low values of the sense resistors, special care must be used to accurately measure the voltage drop across them. specifically, the voltage across each r sense must employ kelvin sensing. this is simply a means of making sure that any voltage drops in the power traces connecting to the resistors are not picked up in addition to the voltages across the sense resistors themselves. if accuracy must be paid for, it?s worth keeping. figure 9 illustrates how kelvin sensing is performed. as can be seen, all the high current in the circuit (let us say, from +5v ina through r sense and then to the drain of the +5va output mosfet) flows directly through the power pcb traces and r sense . the voltage drop resulting across r sense is sampled in such a way that the high currents through the power traces will not introduce any extraneous ir drops. r sense powe r trace from v cc powe r trace to mosfet drain signal trace to mic2590b v cc signal trace to mic2590b v sense figure 9. kelvin sensing connections for r sense mosfet selection selecting the proper mosfet for use as current pass and switching element for each of the 3v and 5v slots of the mic2590b involves four straight forward tasks: 1. choice of a mosfet which meets the minimum voltage requirements. 2. determination of maximum permissible on-state resistance [r ds(on) ]. 3. selection of a device to handle the maximum continuous current (steady-state thermal issues). 4. verification of the selected part?s ability to withstand current peaks (transient thermal issues). mosfet voltage requirements the first voltage requirement for each mosfet is easily stated: the drain-source breakdown voltage of the mosfet must be greater than v in(max) for the slot in question. for instance, the 5v input may reasonably be expected to see high-frequency transients as high as 5.5v. therefore, the drain-source breakdown voltage of the mosfet must be at least 6v.
micrel, inc. mic2590b september 2008 19 m9999-091808 the second breakdown voltage criteria which must be met is a bit subtler than simple drain-source breakdown voltage, but is not hard to meet. low-voltage mosfets generally have low breakdown voltage ratings from gate to source as well. in mic2590b applications, the gates of the external mosfets are driven from the +12v input to the ic. that supply may well be at 12v + (5% x 12v) = 12.6v. at the same time, if the output of the mosfet (its source) is suddenly shorted to ground, the gate-source voltage will go to (12.6v ? 0v) = 12.6v. this means that the external mosfets must be chosen to have a gate- source breakdown voltage in excess of 13v; after 12v absolute maximum the next commonly available voltage class has a permissible gate-source voltage of 20v maximum. this is a very suitable class of device. at the present time, most power mosfets with a 20v gate- source voltage rating have a 30v drain-source breakdown rating or higher. as a general tip, look to surface mount devices with a drain-source rating of 30v as a starting point. mosfet maximum on-state resistance the mosfets in the +3.3v and +5v main power paths will have a finite voltage drop, which must be taken into account during component selection. a suitable mosfet?s datasheet will almost always give a value of on resistance for the mosfet at a gate-source voltage of 4.5v, and another value at a gate-source voltage of 10v. as a first approximation, add the two values together and divide by two to get the on re sistance of the device with 7 volts of enhancement (keep this in mind; we?ll use it in the following thermal issues sections). the resulting value is conservative, but close enough. call this value r on . since a heavily enhanced mosfet acts as an ohmic (resistive) device, almost all that is required to calculate the voltage drop across the mosfet is to multiply the maximum current times the mosfet?s r on . the one addendum to this is that mosfets have a slight increase in r on with increasing die temperature. a good approximation for this value is 0.5% increase in r on per c rise in junction temperature above the point at which r on was initially specified by the manufacturer. for instance, the vishay (siliconix) si4430dy, which is a commonly used part in this type of application, has a specified r ds(on) of 8.0m ? max. at v g-s = 4.5v, and r ds(on) of 4.7m ? max. at v g-s =10v. then r on is calculated as: () 6.35m ? 2 8.0m ? 4.7m ? r on = + = at 25c t j . if the actual junction temperature is estimated to be 110c, a reasonable approximation of r on for the si4430dy at temperature is: () () 9.05m ? c 0.5% 85 1 6.35m ? c 0.5% 25 100 1 6.35m ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? + = ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? + note that this is not a closed-form equation; if more precision were required, several iterations of the calculation might be necessary. this is demonstrated in the section ?mosfet transient thermal issues.? for the given case, if si4430dy is operated at an i drain of 7.6a, the voltage drop across the part will be approximately (7.6a)(9.05m ? ) = 69mv. mosfet steady-state thermal issues the selection of a mosfet to meet the maximum continuous current is a fair ly straightforward exercise. first, arm yourself with the following data: ? the value of i load(cont, max) for the output in question (see sense resistor selection). ? the manufacturer?s data sheet for the candidate mosfet. ? the maximum ambient temperature in which the device will be required to operate. ? any knowledge you can get about the heat sinking available to the device (e.g., can heat be dissipated into the ground plane or power plane, if using a surface mount part? is any airflow available?). now it gets easy: steady-state power dissipation is found by calculating i 2 r. as noted in ?mosfet maximum on- state resistance,? above, the one further concern is the mosfet?s increase in r on with increasing die temperature. again, use the si4430dy mosfet as an example, and assume that the actual junction temperature ends up at 110c. then r on at temperature is again approximately 9.05m ? . again, allow a maximum i drain of 7.6a: () 0.523w 9.05m ? 7.6a r i n dissipatio power 2 on 2 drain ? = ? the next step is to make sure that the heat sinking available to the mosfet is capable of dissipating at least as much power (rated in c/w) as that with which the mosfet?s performance was specified by the manufacturer. formally put, the steady-state electrical model of power dissipated at the mosfet junction is analogous to a current source, and anything in the path of that power being dissipated as heat into the environment is analogous to a resistor. it?s therefore necessary to verify that the thermal resistance from the junction to the ambient is equal to or lower than that value of thermal resistance (often referred to as r (ja) ) for which the operation of the part is guaranteed. as an applications issue, surface mount mosfets are often less than ideally specified in this regard?it?s become common practice simply to state that the thermal data for the part is specified under the conditions ?surface mounted on fr-4 board, t 10seconds,? or something equally mystifying. so here are a few practical tips: 1. the heat from a surface mount device such as an so-8 mosfet flows almost entirely out of the drain leads. if the drain leads can be soldered down to one square inch or more of copper the copper will act as the heat sink for the part. this copper must be on the same layer of the board as
micrel, inc. mic2590b september 2008 20 m9999-091808 the mosfet drain. 2. since the rating for the part is given as ?for 10seconds,? derate the maximum junction temperature by 35c. this is the standard good practice derating of 25c, plus another 10c to allow for the time element of the specification. 3. airflow, if available, works wonders. this is not the place for a dissertation on how to perform airflow calculations, but even a few lfm (linear feet per minute) of air will cool a mosfet down dramatically. if you can position the mosfet(s) in question near the inlet of a power supply?s fan, or the outlet of a processor?s cooling fan, that?s always a good free ride. 4. although it seems a rather unsatisfactory statement, the best test of a surface-mount mosfet for an application (assuming the above tips show it to be a likely fit) is an empirical one. the ideal evaluation is in the actual layout of the expected final circuit, at full operating current. the use of a thermocouple on the drain leads, or in infrared pyrometer on the package, will then give a reasonable idea of the device?s junction temperature. mosfet transient thermal issues having chosen a mosfet that will withstand the imposed voltage stresses, and be able to handle the worst-case continuous i 2 r power dissipation which it will see, it remains only to verify the mosfet?s ability to handle short-term overload power dissipation without overheating. here, nature and physics work in our favor: a mosfet can handle a much higher pulsed power without damage than its continuous dissipation ratings would imply. the reason for this is that, like everything else, semiconductor devices (silicon die, lead frames, etc.) have thermal inertia. this is easily understood by all of us who have stood waiting for a pot of water to boil. in terms related directly to the specification and use of power mosfets, this is known as ?transient thermal impedance.? almost all power mosfet data sheets give a transient thermal impedance curve, which is a handy tool for making sure that you can safely get by with a less expensive mosfet than you thought you might need. for example, take the case where t flt for the 5v supply has been set to 50ms, i load(cont,max) is 5.0a, the slow-trip threshold is 50mv nominal, and the fast-trip threshold is 100mv. if the output is connected to a 0.60 ? load, the output current from the mosfet for the slot in question will be regulated to 5.0a for 50ms before the part?s circuit breaker trips. during that time, the dissipation in the mosfet is given by: [] 2v 5a(0.6 ? a 5v e i e p mosfet = ? = = ( ) 50ms for 10w 5a 2v p mosfet = = wow! looks like we need a really hefty mosfet to withstand just this unlikely?but plausible enough to protect against?fault condition. or do we? this is where the transient thermal impedance curves become very useful. figure 10 shows those curves for the vishay (siliconix) si4430dy, a commonly used so-8 power mosfet. 10 -4 10 -3 10 -2 10 -1 1 10 100 600 2 1 0.1 0.01 0.2 0.1 0.05 0.02 single pulse duty cycle = 0.5 normalized thermal transient imperance, juction-to-ambient 1. duty cycle, d = 2. per unit base = r qja = 67c/w 3. t jm ? t a = p dm z qja (t) 4. surface mounted t 1 t 2 t 1 t 2 notes: p dm square wave pulse duration (sec) normalized e f fective transient thermal impedance figure 10. si4430dy mosfet transient thermal impedance curve
micrel, inc. mic2590b september 2008 21 m9999-091808 using this graph is not nearly as daunting as it may at first appear. taking the simp lest case first, we?ll assume that once a fault event such as the one in question occurs, it will be along time, 10 minutes or more, before the fault is isolated and the slot is reset. in such a case, we can approximate this as a ?single pulse? event, that is to say, there?s no significant duty cycle. then, reading up from the x-axis at the point where ?square wave pulse duration? is equal to 0.1sec (=100ms), we see that the effective thermal impedance of this mosfet to a single pulse event of this duration is only 6% of its continuous r (ja) . this particular part is specified as having an r (ja) of 50c/w for intervals of 10 seconds or less. so, some further math, just to get things ready for the finale: assume t a = 55c maximum, 1 square inch of copper at the drain leads, no airflow. assume the mosfet has been carrying just about 5a for some time. then the starting (steady-state)t j is: t j ? 55c + (7.3m ? )(5a) 2 (30c/w) t j ? 60.5c iterate the calculation once to see if this value is within a few percent of the expected final value. for this iteration we will start with t j equal to the already calculated value of 67c: r on at t j = 60.5c =[1+(60.5c ?25)(0.5%/c)]6.35m ? r on at t j = 60.5c ? 7.48m ? t j ? 55c + (7.3m ? )(5a) 2 (30c/w) t j ? 60.6c at this point, the simplest thing to do is to approximate t j as 61c, which will be clos e enough for all practical purposes. finally, add (10w)(67c/w)(0.0 3) = 21c to the steady- state t j to get t j(transient max) = 82c. the si4430dy can easily handle this value of t j(max) . a second illustration of the us e of the transient thermal impedance curves: assume that the system will attempt multiple retries on a slot showing a fault, with a one second interval between retr y attempts. this frequency of restarts will significantly increase the dissipation in the si4430dy mosfet. will the mosfet be able to handle the increased dissipation? we get the following: the same part is operating into a persistent fault, so it is cycling in a square-wave fashion (no steady-state load) with a duty cycle of (50msec/second = 0.05). on the transient thermal impedance curves, read up from the x-axis to the line showing duty cycle equaling 0.05. the effective r (ja) = (0.7 x 67c/w) = 4.7c/w. calculating the peak junction temperature: t j(peak max) = [(10w)(4.7c/w) + 55c] = 102c and finally, checking the rms power dissipation just to be complete: ( ) ( ) 0.042w 0.05 7.47m ? 5a p 2 rms = = which will result in a negligible temperature rise. the si4430dy is electrically and thermally suitable for this application. mosfet and sense resistor selection guide listed below, by manufacturer and type number, are some of the more popular mosfet and resistor types used in pci hot plug applications. although far from comprehensive, this informat ion will constitute a good starting point for most designs. mosfet vendors key mosfet type(s) web address vishay (siliconix) si4430dy (?littlefoot? series) si4420dy (?littlefoot? series) www.siliconix.com international rectifier irf7413a (so-8 package part) si4420dy (second source to vishay) www.irf.com fairchild semiconductor fds6644 (so-8 package part) fds6670a (so-8 package part) fds6688 (so-8 package part) www.fairchildsemi.com resistor vendors sense resistors web address vishay (dale) ?wsl? series www.vishay.com/docs/wsl_30100.pdf irc ?oars? series ?lr? series (second source to ?wsl?) irctt.com/pdf_files/oars.pdf irctt.com/pdf_files/lrc.pdf
micrel, inc. mic2590b september 2008 22 m9999-091808 power supply decoupling in general, prudent system design requires that power supplies used for logic functions should have less than 100mv of noise at frequencies of 100khz and above. this is especially true given the speeds of moden logic families, such as the 1.2micron cmos used in the mic2590b. in particular, the ?12v supply should have less than 100mv of peak-to-peak noise at frequencies of 1mhz or higher. this is bec ause the ?12v supply is the most negative potential applied to the ic, and is therefore connected to the device's substr ate. all of the subcircuits integrated onto the silicon chip are hence subjected by capacities coupling to any hf noise on the ?12v supply. while individual capacitances ar e quite low, the amount of injected energy required to cause a "glitch" can also be quite low at the internal nodes of high speed logic circuits. less obviously, but equally important, is the fact that the internal charge pump for the 3.3v aux supplies is somewhat susceptible to noise on the +12v input when that input is at or near zero volts. the +12v supply should not carry hf noise in excess of 200mv peak-to-peak with respect to chip ground when it is in the "off" state. if either the ?12v input, the +12v input, of both supplies do carry significant hf noise (as can happen when they are locally derived by a swit ching converter), the solution is both small and inexpensive. an lc filter made of a ferrite bead between the noisy power supply input and the mic2590b, followed by a "composite capacitor" from the affected mic2590b input pin to ground will suffice for almost any situation. a good composite capacitor for this purpose is the parallel combination of a 47f tantalum bulk decoupling capacitor, and one each 1f and 0.01f ceramic capacitors for high-frequency bypass. a suggested ferrite bead for such use is fair-rite products corporation part number 2743019447 (this is a surface- mountable part). similar parts from other vendors will also work well, or a 0.27h, air-core coil can be used. noisy v in to mic2590b smt ferrite bead fair-rite products type 2743019447 47f tantalum 1f ceramic 10nf ceramic figure 11. filter circuit for noisy supplies (+3.3v and/or ?12v) it is theoretically possible that high-amplitude, hf noise reflected back into one or both of the mic2590b?s ?12v outputs could interfere with proper device operation, although such noisy loads are unlikely to occur in the real world. if this becomes an app lication-specific concern, a pair of filters similar to that in figure 11 will provide the required hf bypassing. the capacitors would be connected to the mic2590b?s ?12v output pins, and the ferrite beads would be placed between the ?12v output pins and the loads. ?12v input clamp diode the ?12v input to the mic2590b is the most negative potential on the part, and is therefore connected to the chip?s substrate (as described in ?power supply decoupling,? above). although no particular sequencing of the ?12v supply relative to the other mic2590b supplies is required for normal operat ion, this substrate connection does mean that the ?12v input must never exceed the voltage on the ground pin of the ic by more than 0.3 volts. in some systems, even though the ?12v supply will discharge towards ground potential when it is turned off, the possibility exists that power supply output ringing or l(di/dt) effects in the wiring and on the pcb itself will cause brief transient voltages in excess of +0.3v to appear at the ?12v input. the simplest way to deal with such a transient is to clamp it with a schottky diode. the diode?s a node should be physically placed directly at the ?12v input to the mic2590b, and its cathode should have as short a path as possible back to the part?s ground. a good smt part for this application is on semiconductor?s type mbrs140t3 (1a, 40v). although the 40v rating of this part is a bit gratuitous, it is an inexpensive industry- standard part with many second sources. unless it is absolutely known in advance that the voltage on the ?? 12v? inputs will never exceed 0.0v at the ic?s ?12v input pins, it?s wise to at least leave a position for this diode in the board layout and then remove it later. this final determination should be made by observations of the voltage at the ?12v input with a fast storage oscilloscope, under turn-on and turn-off conditions. gate resistor guidelines the mic2590b controls four external power mosfets, which handle the high currents for each of the two 3.3v and 5v outputs. a capacitor (c gate ) is connected in the application circuit from each gate pin of the mic2590b to ground. each c gate controls the ramp-up rate of its respective power output (e.g., 5v outb ). these capacitors, which are typically in the 10nf range, cause the gate outputs of the mic2590b to have very low ac impedances to ground at any significant frequency. it is therefore necessary to place a modest value of gate damping resistance (r gate ) between each c gate and the gate of its associated mosfet. these resistances prevent high-frequency mosfet source-follower oscilla- tions from occurring. the exact value of the resistors used is not critical; 47 ? is usually a good choice. each r gate should be physically located directly adjacent to the mosfet gate lead to which it connects. mic2590b gate r gate c gate external mosfet figure 12. proper connection of c gate and r gate
micrel, inc. mic2590b september 2008 23 m9999-091808 package information , s n o i s u r t o r p r o h s a l f d l o m e d u l c n i t o n s e o d n o i s n e m i d . m m 4 5 2 . 0 d e e c x e t o n l l a h s h c i h w f o r e h t i e . n o i s u r t o r p r a b m a d e d u l c n i t o n s e o d n o i s n e m i d d a e l m o t t o b n a h t r e l l a m s e r a s n o i s n e m i d d l o m p o t e g a k c a p g n a h r e v o t o n l l i w e g a k c a p f o p o t d n a s n o i s n e m i d d l o m . e g a k c a p f o m o t t o b : s e t o n . 1 . 2 . 3 . 4 48-pin tqfp (tq) micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com the information furnished by micrel in this data sheet is believ ed to be accurate and reliable. however, no responsibility is a ssumed by micrel for its use. micrel reserves the right to change circuitry and spe cifications at any time without notification to the customer. micrel products are not designed or author ized for use as components in life support app liances, devices or systems where malfu nction of a product can reasonably be expected to result in personal injury. life s upport devices or systems are devices or systems that (a) are in tended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significan t injury to the user. a purchaser?s use or sale of micrel products for use in life support appliances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2002 micrel, incorporated.

▲Up To Search▲

Price & Availability of MIC2590B11

	To Download MIC2590B11 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .